If Revit does not support full-fledged curved sections OOTB, then you cannot create them programmatically either. However, you could perfectly well create something quite similar yourself using the API. The most difficult part to achieve might be full associativity.
Quick Answer, how do you take a curved section? Set the section view properties: Hold down Shift and on the Views tab, click Curved section view. Modify the view properties as required, and click OK or Apply. Pick three points on the cut plane. Pick two points to indicate the cut box.
You asked, how do you make curves in Revit?
As many you asked, can a section line be curved? no you can’t. You have to do it with linear section lines.
Also the question is, how do you create a curved extrusion in Revit?
- Create the curves you will use for the profile and path.
- Choose Surfaces > Swept Surfaces > Extrude from the tool palette.
- Pick the curve or curves you want to extrude.
- Click Go.
- Pick the path curve to extrude along.
How do you build a curved wall?
How do you radius a Revit fillet?
- Select a tool that allows for an arc.
- Click Modify | Place Lines tab (or respective Modify | Place
tab or Modify | Create tab) Draw panel (Fillet Arc), and place the cursor in the drawing area. - Select the first element to fillet.
- Select the second element to fillet.
How do you make an angled section in Revit?
How do you create a broken section in Revit?
How do you break a section line in Revit?
- Click the break control ( ) and adjust the length of the section line segments.
- To rejoin the section line, click the break control again. Note: A break in a section line is view-specific. It affects the display of the section only in the view where the break was made.
How do you make a curved ceiling in Revit?
How do you round edges extrusion in Revit?
How do you make a curved block wall?
What is a curved wall called?
A crinkle crankle wall, also known as a crinkum crankum, sinusoidal, serpentine, ribbon or wavy wall, is an unusual type of structural or garden wall built in a serpentine shape with alternating curves, originally used in Ancient Egypt, but also typically found in Suffolk in England.
How do you frame a curved bar?
How do you curve a corner in Revit?
- Choose Surfaces > Round .
- Select three or four edges (each shared by two surfaces) that meet at a corner.
- Click on a radius manipulator handles to move it or change the radius value (See the section Using the Radius manipulator for more information).
How do you curve a wall corner in Revit?
How do you use a fillet arc in Revit?
- Select a tool that allows for an arc.
- Click Modify | Place Lines tab (or respective Modify | Place
tab or Modify | Create tab) Draw panel (Fillet Arc), and place the cursor in the drawing area. - Select the first element to fillet.
- Select the second element to fillet.
How do you cut a zig zag section in Revit?
Select it, Then in the ribbon under Modify / Views, click the “Split Section” button. the cursor will show a knife. click on the section where you want to make the cut and drag the section to make the kinked split.
Can you rotate a section box?
User’s Guide: Rotating a Section View or Scope Box. Open the project view that contains the section (callout) or scope box to rotate. Select the section (callout) or scope box. Click Modify
How do you create a longitudinal section in Revit?
What is a jogged section?
A jog that is added to an existing section object creates a segment that is perpendicular to the selected segment. Its viewpoint is oriented in the direction set by the Direction grip. The Nearest object snap is temporarily turned on to help you place the jogs on a section.
How do you split sections?
- Select where you want a new section to begin.
- Go to Layout > Breaks.
- Choose the type of section break you want: Next Page Section break starts the new section on the following page. Continuous Section break starts the new section on the same page.